How to install white LED under side mirror Puddle Lights on VW Golf 6 Mk6, Jetta in 25 steps
In this video tutorial we are going to show you how to install white LED under side mirror puddle lights on VW Golf 6 Mk6, Jetta in 25 simple steps.
HERE you can find LED Side Mirror Puddle Light Super Bright Xenon White for 2010-2014 VW Golf Mk6, Golf GTI: https://amzn.to/3dbxhFq
UK & Europe customers can find Under Side Mirror Puddle 6 LED Lights for VW GTI / Golf MK6 6 / MKVI 2010-2014 HERE: https://amzn.to/3mIoazR
US customers can find Under Side Mirror Puddle 6 LED Lights for VW GTI / Golf MK6 6 / MKVI 2010-2014 HERE: https://amzn.to/3M2cgM5
HERE you can find VCDS (VAGCOM) scan tool at the BEST PRICE:
Required tools:
– M8 triple square bit or Torx T40 and a T25 torx (you can find 12-Piece Magnetic Torx Screwdrivers Set HERE: https://amzn.to/3s9GceR)
– VCDS scan tool (here you can find VCDS / VAGCOM scan tool: )
– trim tool (here you can find Trim Tool Setr: https://amzn.to/3uy4FMd)
– soldering gun: https://amzn.to/39q2Qc6
– cutter knife: https://amzn.to/2Pa8UPf
– silicone: https://amzn.to/3s78uq1
– flat blade screwdriver: https://amzn.to/3thkKWs
– shrink tubing: https://amzn.to/3rAeOX4
– heat gun: https://amzn.to/3dbykUk
– Genuine Repair Wire for VW, Audi, Skoda Golf, Passat:
Before you start installing it, first you have to buy and connect two (red) (000979018E) to the mirror puddle lights.
One of the wires has to be 10 cm long and the other one 20 cm.
1. Remove the glass mirror using both hands
2. Disconnect the cables from the mirror glass
3. Remove all 5 screws using a T20 Torx
4. Remove the adjuster and the cables
5. Remove the mirror cover from the clips
6. Remove the black part
7. Remove the black cover from the lower side of the mirror
Then you have to drill a hole in the lower mirror cap.
8. Disconnect the cables
9. Remove the door panel (see video tutorial on www.servicetutorials.com) and disconnect the cables from the tweeter
10. Remove the tweeter
11. Remove the mirror bolt using a M8 triple square bit or a T40 Torx
12. Remove the wing mirror arm
13. Take the long wire (repair wire) from the puddle light and route it along the small connector with red lock
14. Remove the small connector with the red lock and take the housing out
15. Insert the long wire (repair wire) from the puddle light into slot 10
16. Install the wing mirror arm
17. Put the screw back
18. Connect the mirror signal wires and install the mirror lower housing
19. Use silicone to seal the puddle light to the lower mirror cap
20. The other wire from the puddle light solder to the heating wire („minus”)
Cover the wires in shrink tubing.
21. Install the power mirror motor
22. Install all the mirror parts
23. Connect the wires to the mirror glass and install it
24. Install the tweeter and door panel
25. Use a VCDS (VAG COM) dyagnose to activate „Ambient Mirror Illumination installed” function using these next steps:
For the left side mirror: Select Control Module / 42-Door Elect, Driver / Coding-07 / Coding Helper / Byte 2 and select „Ambient Mirror Illumination installed” / Exit / Do it! / Ok / Close Controller, Go Back – 06
For the right side mirror: Select Control Module / 52-Door Elect, Pass. / Coding-07 / Coding Helper / Byte 2 and select „Ambient Mirror Illumination installed” / Exit / Do it! / Ok / Close Controller, Go Back – 06 / Go Back / Exit.
See more VIDEO TUTORIALS for Volkswagen Golf Mk6 / Touran:
How to activate auto folding side mirrors on VW Golf MK6, Mk7, GTI, Jetta, Passat B7, CC in 3 steps!
How to install LED Footwell lights on VW Golf Mk6, Jetta in 12 simple steps!
How to install front door puddle lights on VW Golf Mk6, Jetta!
If you have any suggestions about new tutorials, let us know in the comments section!
If you enjoyed this video tutorial, make sure to give it a thumbs up and share it with your friends.